Kargo-master Econo Truck Rack – With Camper Shell (30060) Manuel d'utilisateur télécharger pdf

( HIGH POSITION )

STEP 1-

NOTE: If it is not possible to locate a second hole close to the front

leg because of the stake pocket, use our stake pocket T bolt mount

kit (#31560) purchased separately.

CHECK TWICE - DRILL ONCE!

Monday- Friday 8:00 A.M. to 4:30 P.M. (PACIFIC )

2 BAR ECONO CAMPER SHELL RACK

Assembly Instructions

1-800-343-7486

For TECHNICAL SUPPORT Call:

(8 ea.)

3/8" Lock Nut

3/8" Flat Washer

(8 ea.)

3/8" x 1/2"

Allen Head

Set Screw

#30060

(8 ea.)

3/8" x 1 3/4"

Hex Bolt

• To install the rear ECONO TRUCK RACK on your truck bed, repeat the above. Before drilling the mounting plate, make sure that the plate

dose not overhang or interfere with the tail gate. Before inserting the Caps, make sure that the height setting in the rear matches the height

setting in the front.

STEP 3- Your rack can be set high or low by flipping the CROSSBAR SUPPORT, (as shown) Determine

which is best for your vehicle and your cargo. For bowed canoes, we recommend the high position.

STEP 5- Insert the CROSSBAR into the CROSSBAR SUPPORTS and set the entire

assembly on top of the legs. Cut CROSSBAR to shorten length, IF NEEDED, for the width

of a mini-truck bed. CENTER THE CROSSBAR LEFT TO RIGHT, and secure with set

screws. Secure the CROSSBAR SUPPORT UPRIGHT to each leg with set screws.

BOLT KIT

THAT'S IT!

You're ready to load and go!

Tighten all bolts and....

Be sure FRONT MOUNTING PLATES are as far

forward towards the cab as possible. Find the pre-drilled hole

in the footplate that is furthest from the leg and drill

3/8” hole

through truck’s bed rail. You must drill a second bolt hole through

both the footplate and the truck’s bed rail. Locate this second hole

as close as possible to the front leg, but making sure you can

access the end of the bolt underneath the truck’s bed rail as

necessary to put on the washer and nut. Attach the footplate to

the truck using bolts

A, washers B and nuts C .

DO NOT OVER TIGHTEN ON DOUBLE WALL BED CONSTRUCTION, AS THIS MAY DEFORM THE SHEET METAL OF THE PICKUP BED!

( LOW POSITION )

Crossbar Support Upright

STEP 4- Plug the TOP of the CROSSBAR SUPPORT UPRIGHT with caps provided.

(8 ea.)

1/2" x 1"

Hex Bolt

(5 ea.)

1/2" Lock Washer

(15 ea.)

1/2" SAE Flat Washer

Leg

Mount Plate

INSIDE

BED WALL

Outside of

Truck Bed

CAMPER SHELL

STEP 2- Replace camper shell with appropriate weather stripping . Attach legs

loosely to mounting plates with bolts

P, lock washers O, and flat washers H.

Résumé du contenu

Page 1 - Assembly Instructions

( HIGH POSITION )DSTEP 1- NOTE: If it is not possible to locate a second hole close to the front leg because of the stake pocket, use our stake pocke

Commentaires sur ces manuels

Pas de commentaire

Kargo-master Econo Truck Rack – With Camper Shell (30060) Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Kargo-master Econo Truck Rack – With Camper Shell (30060). Kargo Master Econo Truck Rack – With Camper Shell (30060) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Kargo-master Econo Truck Rack – With Camper Shell (30060)